Tiza Group

Home / Guides / Equipment, switchboards and substations

Switchboard Maintenance: Plan, Tasks and Intervals

How to plan switchboard maintenance for low-voltage equipment: tasks, intervals by condition and criticality, what to inspect, measure and record.

By Shadai García, CEO and protection engineer at Tiza Group.

MT/BTGinterlockATSLV busMMfeederCCMauxiliariesbusesUF 1UF 2UF 3term.Form 1no partitionsForm 2separate busbarsForm 3separate unitsForm 4separate terminalsIEC 61439-2: forms of internal separationIntegrationLSIG unitGatewaySCADA© tizagrp.comMT/BTGinterlockATSLV busMMfeederCCMauxiliariesbusesUF 1UF 2UF 3term.Form 1no partitionsForm 2separate busbarsForm 3separate unitsForm 4separate terminalsIEC 61439-2: forms of internal separationIntegrationLSIG unitGatewaySCADA© tizagrp.com
LV switchboard and MCC: automatic transfer and forms of separation. Location in the system and operating principle. Illustrative: real values come from the nameplate and the manufacturer's manual.
Short answer

Switchboard maintenance is organized as a program: equipment inventory, condition assessment, tasks with intervals and records of findings. NFPA 70B, a standard since its 2023 edition, sets intervals from condition, criticality and environment. Core tasks are visual inspection, infrared thermography under load, torque checks, cleaning and insulation and breaker tests.

Short answer

Switchboard maintenance is a program, not a visit: the switchboards are inventoried, each one’s condition is assessed, tasks and intervals are set and findings are recorded. NFPA 70B, which since its 2023 edition is a standard with requirements and not only a recommended practice, sets the interval from three factors: physical condition, criticality and environment. For a plant-wide view see NFPA 70B: electrical maintenance.

What is maintained and why switchboards fail

An LV switchboard ages for three reasons: heat (loose connections, overload), environment (dust, moisture, corrosion, animals) and mechanical wear (breakers and contactors that operate). Almost everything found in an inspection falls into one of these. The structure of the assembly, its busbars and forms of separation are in LV switchboard and MCC.

Program tasks

TaskWhat it detectsState of the switchboard
Visual inspectionCorrosion, discoloration, dust, moisture, mechanical damage, illegible labelsClosed or open, by zone
Thermography under loadConnections and contacts that run hotEnergized, under load
Tightening of connectionsLoose connectionsDe-energized, locked out and verified
CleaningConductive dust, debris, insectsDe-energized
Insulation resistanceDeterioration of busbar and circuit insulationDe-energized
Breakers and contactorsWear, trip that does not operate, interlocksDe-energized, with tests
Control and signalingAlarms, relays, lamps, communicationsCase by case

Two safety rules are not negotiable. Any work inside the switchboard follows lockout and tagout, verification of absence of voltage and the arc-flash protection that applies (NFPA 70E, with incident energy from IEEE 1584). And thermography is done with doors open only if someone with proper protection can do it; infrared windows allow inspection with the switchboard closed, which is a design decision worth making at the specification stage.

Interval by condition

NFPA 70B asks that each piece of equipment receive a condition assessment on three factors, its physical condition, criticality and environment, and that the worst one define the condition and with it the interval. Thermography is the most repeated task, and its interval shortens when the equipment has outstanding problems.

How often should this switchboard be reviewed?
  • Does a failure stop a critical process or put people at risk?
    • Yes: Does it have outstanding problems?
      • Yes: Short interval and correct what is pending
      • No: Interval according to condition, reviewed every year
    • No: Is the environment harsh (dust, moisture, corrosion)?
      • Yes: Shorten the interval and reinforce cleaning
      • No: Standard interval according to condition

The interval of each task is set by the program, with the recommendations of the manufacturer of the assembly and its devices where they exist.

Worked example: a hot spot at low load

During a thermographic survey at 10 a.m., a 630 A outgoing breaker shows phase A at 46 °C and phases B and C at 40 °C. The measured current is 252 A, 40 % of rated. The difference with similar components is 6 °C.

The heat of a poor connection grows with the square of the current. Projected to full load:

  • Current ratio: 630 ÷ 252 = 2.5.
  • Factor: 2.5² = 6.25.
  • Projected difference: 6 °C × 6.25 = 37.5 °C.

At 6 °C the finding looks minor. Projected to full load it far exceeds the 15 °C that Table 100.18 of ANSI/NETA MTS-2015 treats as a major discrepancy between similar components, with immediate repair. The practical conclusion: the point is corrected at the next outage, not postponed, and the image is repeated at higher load. The projection is a simple estimate; the report must state which criterion it used for classification.

Intervention checklist

  • Scope, date and responsible person in writing, with an up-to-date single-line diagram.
  • Lockout, tagout and verification of absence of voltage before opening.
  • Current of each circuit noted during thermography.
  • Torque checked with a calibrated tool and what was tightened marked.
  • Insulation readings with date and ambient temperature.
  • Operation test of breakers, interlocks and alarms.
  • Findings classified: corrected, pending with date, or for the next outage.
  • Report with photos and recommendations.

When to maintain and when to upgrade

Maintenance has a limit. When the switchboard can no longer be maintained safely or with spare parts, an upgrade, or retrofit, is evaluated: replacing breakers, contactors or control units while keeping the structure. The typical signs are:

  • Discontinued spare parts or no manufacturer support.
  • Network short-circuit current higher than the switchboard withstands, because the installation has grown.
  • Breakers whose findings repeat after every intervention.
  • Load changes that exceed the rated current of the switchboard.
  • Missing interlocks or arc protection that are required today.

Each decision rests on the program records: without a history of findings, an upgrade is decided blindly.

What not to do

Do not tighten by feel, do not blow out conductive dust with compressed air without removing it first, do not isolate a finding and forget it, and do not maintain only after a failure. Also, do not compare a thermographic image directly with the temperature-rise limits of IEC 61439-1: those are values from the design-verification test. The guide on temperature-rise limits explains why.

How we help

We provide the engineering of the maintenance program for low-voltage switchboards, from the criticality ranking and interval setting to the specification of access, infrared windows and records: contact us with your switchboard list and we will propose the program.

References

  • NFPA 70B, Standard for Electrical Equipment Maintenance, 2023 edition; NFPA published a 2026 edition that replaces it.
  • ANSI/NETA MTS-2015, Standard for Maintenance Testing Specifications for Electrical Power Equipment and Systems, Table 100.18. The current edition is 2023.
  • IEC 61439-1, Low-voltage switchgear and controlgear assemblies: general rules.
  • NFPA 70E, Standard for Electrical Safety in the Workplace.
  • IEEE 1584, Guide for Performing Arc-Flash Hazard Calculations.

Frequently asked questions

How often should a switchboard be maintained?

It depends on its condition, criticality and environment; there is no single interval. NFPA 70B, since its 2023 edition, starts from the condition of each piece of equipment: the worse the condition, the shorter the interval.

What can be done while the switchboard is energized?

With the switchboard energized, and doors closed or infrared windows fitted, external visual inspection and thermography under load can be done. Tightening connections, internal cleaning and insulation tests require de-energizing, lockout and tagout, and verification of absence of voltage.

What should be recorded after maintenance?

The date, the equipment, the load conditions, what was found, what was corrected and what is pending, with photos or thermal images and the insulation and torque readings. These records feed the program: they allow one visit to be compared with the previous and the intervals to be adjusted.

WhatsApp