NEC Article 450 covers the installation of transformers. Section 450.3 sets the maximum overcurrent protection for the windings. With primary-only protection the device is limited to 125 percent of the rated primary current. With protection on both sides, the primary limit rises to 250 percent and the secondary is limited to 125 percent. The article also covers ventilation, marking, accessibility, installation locations and vaults. Conductor protection is a separate calculation.
NEC article 450 transformers is the part of the National Electrical Code (NEC, NFPA 70) that covers how a transformer is installed: how it is protected, ventilated, marked, reached and housed. It applies to the dry-type transformer in a mechanical room as it does to the liquid-filled unit behind a plant.
The wider framework is in the US electrical codes and grid interconnection guide. The equipment itself is explained in the guide on the MV/LV distribution transformer, and the sizing of the unit in how to size a transformer.
Section numbers here follow the 2023 edition of the NEC. The 2026 edition is current, but the authority having jurisdiction (AHJ) decides which one applies. Confirm numbering and local amendments in the adopted edition.
Short answer
Section 450.3 limits the overcurrent device that protects the windings of a transformer. For a transformer with a rated primary current of 9 A or more, primary-only protection is limited to 125 percent of that current, with a permitted step up to the next standard rating. If both the primary and the secondary have protection, the primary limit rises to 250 percent, and the secondary is limited to 125 percent. Over 1,000 V, a separate table in the same section applies. These limits protect the transformer, not the conductors, which are protected under Article 240.
What the article covers
- Overcurrent protection (450.3). The maximum size of the device for the windings, in two tables: one for voltages over 1,000 V and one for 1,000 V or less.
- Ventilation (450.9). Air must be able to reach and leave the unit, and the openings cannot be blocked.
- Marking (450.11). A nameplate with manufacturer, rating, voltages and, for larger units, impedance.
- Accessibility (450.13). Transformers have to be reachable by qualified people, with exceptions for some dry-type units.
- Location and type. Different rules for dry-type, less-flammable liquid-filled and oil-filled transformers, indoors and outdoors, including fire separation.
- Vaults. Rooms for transformers with their own construction, door and ventilation rules.
Other articles cover grounding of the transformer neutral and enclosures (Article 250 is the reference for that), and the protection of conductors is part of Article 240.
Two ways to protect a transformer
The 1,000 V and below table offers two arrangements:
- Primary-only protection. One device on the primary side, limited to 125 percent of the rated primary current. If that value is not a standard rating, the next higher standard size is allowed. The secondary conductors still need their own protection under 240.21(C). A primary device protects them only for a single-phase two-wire or a three-phase delta-delta three-wire secondary.
- Primary and secondary protection. The primary can be up to 250 percent of the rated primary current, because the secondary device is also there and limited to 125 percent of the rated secondary current. This arrangement allows a primary device large enough to ride through the inrush of the transformer. For the physics of the inrush, see energizing a transformer: inrush current.
Notes in the code give exceptions for lower currents and for some conditions in which the secondary device can be omitted. Read them in the adopted text.
Protection of the transformer is not protection of the conductors
The 450.3 limits do not size the conductors. Primary conductors are protected by the primary device or by a tap rule, and secondary conductors need protection that suits their ampacity, which brings in Article 240 and the tap rules of that article. A secondary device that is allowed for the transformer might still be too large for the cable that leaves it. The conductor sizing itself is the subject of the guide on conductor ampacity under Article 310.
Medium voltage
Over 1,000 V, the same section gives a separate table with different multipliers for the primary and the secondary, for fuses and for breakers. In many projects the utility or the plant protection engineer sets the medium-voltage protection with a coordination study, and the NEC value serves as the upper limit. The choice between a fuse and a breaker is covered in fuse or circuit breaker to protect an MV transformer.
Location, ventilation and marking
Practical points an inspector checks:
- Clearances around the unit match what the manufacturer and the code require.
- Ventilation openings are free and sized for the losses of the unit.
- The nameplate is legible and agrees with the drawings.
- Dry-type units in rooms with combustibles have the separation or enclosure the code asks for.
- Liquid-filled units have the containment and fire protection their type requires.
The choice between a dry-type and an oil-filled unit is covered in dry-type versus oil-immersed transformers.
Figure: single-line of a 480 V to 208Y/120 V transformer with primary and secondary overcurrent devices and the conductors on both sides.
Worked example: a 75 kVA transformer
The data are illustrative. A 75 kVA dry-type transformer, 480 V delta primary and 208Y/120 V secondary, three-phase.
- Rated primary current: 75,000 / (1.732 × 480) = 90.2 A.
- Rated secondary current: 75,000 / (1.732 × 208) = 208.2 A.
- Primary-only protection: 90.2 × 1.25 = 112.8 A. The next higher standard rating, 125 A, is allowed. With a 208Y/120 V secondary, the secondary conductors still need protection or a tap rule under 240.21(C).
- Primary and secondary protection: the primary limit is 90.2 × 2.5 = 225.5 A. A 225 A device stays under that. The secondary limit is 208.2 × 1.25 = 260.2 A, so a 250 A device is below the limit. The next higher standard rating, 300 A, would also be allowed for the transformer, but the conductor decides.
- Check the conductors separately. A 125 A primary device needs conductors with at least that ampacity, or a tap that qualifies under Article 240. The 250 A secondary device needs a secondary conductor with an ampacity of at least 250 A, which in turn needs the terminal rating and corrections.
- Check the inrush. A transformer can draw several times its rated current for a few cycles on energizing. A larger primary device, as in step 4, helps the unit ride through it.
The table limits are ceilings. The selection can be lower if the load and the inrush allow.
Checklist for the engineer
- Confirm the NEC edition and amendments adopted by the AHJ.
- Calculate the rated primary and secondary currents from the nameplate.
- Choose primary-only or primary and secondary protection, and apply the limits of the correct table.
- Check the conductors on both sides under Articles 240 and 310.
- Check inrush against the primary device.
- Check ventilation, clearances, marking and the room or vault requirements.
- Check the available fault current on both sides of the transformer.
- For medium voltage, align the design with the utility and the protection study.
Who signs and seals
In the United States a design normally has to be signed and sealed by a professional engineer licensed in the state of the project. The AHJ and often the utility review transformer installations.
From the rules to a design your engineer can stamp
Tiza provides power-system studies and engineering design for transformer installations: short-circuit and protection coordination, inrush checks and single-line diagrams, ready for your engineer of record to review and stamp. Tiza does not sign, seal or certify work in the United States. Contact us with the nameplate, the single-line diagram and the utility data.
Frequently asked questions
What does NEC 450.3 say about transformer protection?
Section 450.3 limits the size of the overcurrent device that protects the transformer windings. For a transformer with a primary current of 9 A or more and primary-only protection, the device is limited to 125 percent of the rated primary current. With protection on both sides, the primary limit rises to 250 percent and the secondary is limited to 125 percent.
Does transformer overcurrent protection also protect the conductors?
No. The limits in 450.3 protect the transformer. The primary and secondary conductors need their own protection under Article 240, and the tap rules of that article decide whether a secondary device is needed for them.
Does Article 450 apply to utility transformers?
Article 450 is part of the premises wiring rules. Equipment owned and operated by a utility is generally covered by other documents, such as the utility's own standards and the National Electrical Safety Code. Confirm the point of ownership and the applicable rule with the utility and the AHJ.