NEC Article 480 covers stationary batteries as a wiring and installation subject: disconnecting means, locations, racks, terminals and, in the 2026 edition, overcharge control. In the 2023 edition the article was limited to stationary standby batteries above 1 kWh. The 2026 edition removed the word standby from the scope. Battery energy storage systems, which are listed as a whole, are the subject of Article 706.
NEC article 480 storage batteries is the part of the National Electrical Code (NEC, NFPA 70) that covers stationary batteries as an installation. It deals with how they are disconnected, where they sit and how they are arranged. It is often confused with the article on energy storage systems, and the confusion changes the whole design review.
The wider framework is in the US electrical codes and grid interconnection guide. For the technical side of sizing and testing a battery bank, see the existing guides on sizing stationary batteries and on lead-acid and nickel-cadmium batteries.
The 2023 and 2026 editions of the NEC are compared here. Many jurisdictions enforce 2023 or earlier, sometimes with amendments, so confirm the edition your authority having jurisdiction (AHJ) has adopted.
Short answer
Article 480 applies to stationary batteries as installed. In the 2023 edition its title referred to stationary standby batteries, and its scope covered standby installations above 1 kWh. The 2026 edition dropped standby from the title and scope and added section 480.14 on overcharge control. Listed battery energy storage systems fall under Article 706 instead. The article asks for a disconnecting means above a stated voltage (section 480.7). It also asks for racks and locations that suit the battery type, and for ventilation where the chemistry calls for it.
What the article covers
Article 480 is about the installation of the battery, not the chemistry. Typical subjects are:
- Disconnecting means (480.7). A way to open the ungrounded conductors from the battery system.
- Racks and trays (480.9). Supports that resist the electrolyte and carry the load.
- Locations and ventilation (480.10 and following). Where the battery may sit and how gases are handled.
- Terminals, wiring and overcurrent protection. How the battery is connected to the rest of the system.
Several definitions that used to sit in Article 480 moved to Article 100 in the 2023 edition. Substation batteries, telecom batteries and UPS batteries are the common users. The guides on substation battery autonomy and on the battery that does not hold the load cover the operating side.
2023 against 2026
| Topic | 2023 edition | 2026 edition |
|---|---|---|
| Title and scope | Stationary standby batteries above 1 kWh | Stationary batteries above 1 kWh, standby or not |
| Overcharge control | Not a section of its own | New section 480.14 |
| Definitions | Moved to Article 100 | Same location |
The numbers of the sections discussed here (480.7, 480.9 and 480.10) come from the 2023 edition. A designer who works from the 2026 text should check the numbering of every section cited in drawings and specifications.
Where Article 706 takes over
A battery energy storage system is more than a battery. It has an inverter or power conversion, a battery management system, thermal control and its own protection. A listed system of that type is handled under Article 706, which the US electrical codes guide places in the installation layer along with Articles 690 and 705.
Article 480 still matters in two ways:
- For batteries that are not part of a listed storage system, such as a station battery, a UPS battery room or telecom plant.
- As a reference for battery rooms where the 2026 scope now reaches more battery types.
The technical guides on lithium-ion battery safety and service life and on the parts and functions of a BESS explain why the two subjects are kept apart.
Figure: dc circuit of a UPS with its charger, battery string, battery disconnect, protection and the dc bus to the inverter.
Worked example: a 120 V UPS battery string
The data are illustrative. A 30 kW UPS has an inverter efficiency of 94%. The battery string has 60 lead-acid cells at 2.0 V nominal, a float voltage of 2.25 V per cell and an end-of-discharge voltage of 1.75 V per cell. The required runtime is 15 minutes.
- Nominal string voltage: 60 × 2.0 = 120 V. That is above 60 V dc, so a disconnecting means is expected under 480.7.
- Float voltage: 60 × 2.25 = 135 V. This is the voltage that the charger and the equipment must tolerate.
- End voltage: 60 × 1.75 = 105 V. The battery supplies the load down to this point.
- DC power at the load: 30 / 0.94 = 31.9 kW.
- DC current at the end voltage: 31,900 / 105 = 304 A. The disconnect, the conductors and the protection must be selected for this current and for the available fault current of the string, which the manufacturer provides.
- Energy for the runtime: 31.9 × 0.25 h = 8.0 kWh. The manufacturer’s discharge tables set the actual capacity, so this is a check and not a selection.
The sequence is the point: voltage first, then current, then energy. The IEEE methods used to size the bank are in the guide on an example of battery sizing under IEEE 485.
Checklist for the engineer
- Confirm the NEC edition and amendments adopted by the AHJ.
- Decide whether the battery is a stationary battery under Article 480 or part of a listed system under Article 706.
- Identify the chemistry and read the scope of the adopted edition for that chemistry.
- Provide a disconnecting means for the battery conductors that meets the voltage rule of the edition.
- Check the available fault current of the battery with the manufacturer and the rating of every device on the string.
- Check racks, location, ventilation and clearances for the chemistry.
- Check the overcharge control and the charger settings, including the 2026 requirement if it applies.
- Label the battery and the disconnect, and keep the manufacturer data with the project record.
Who signs and seals
In the United States a design normally has to be signed and sealed by a professional engineer licensed in the state of the project. Battery rooms are often reviewed by the fire authority as well as the electrical inspector.
From the code to a design your engineer of record can stamp
When your project needs the single-line diagram, the battery sizing and the protection design for a battery room, Tiza delivers engineering design ready for your engineer of record to review and stamp, remotely and in English. Tiza does not sign, seal or certify work in the United States. Contact us with the load profile, the battery data and the NEC edition your AHJ enforces.
Frequently asked questions
Does Article 480 apply to lithium-ion battery energy storage systems?
Mostly no. A listed energy storage system with its own controls and protection is the subject of Article 706. Article 480 deals with stationary batteries as installed equipment. The 2023 edition limited it to stationary standby batteries, and the 2026 edition widened the scope to stationary batteries in general above 1 kWh.
What changed in Article 480 in the 2026 edition?
The word standby was removed from the scope, so the article covers stationary batteries in general, and a new section 480.14 adds an overcharge control requirement.
Is a disconnect required for a battery bank?
Article 480 asks for a disconnecting means for the ungrounded conductors of a stationary battery system above a stated voltage, which is 60 volts dc. Section 480.7 also sets the location and the arrangement of that disconnect.