Tiza Group

Home / Guides / Codes and grid connection: US, UK, CA, AU

NEC Article 408: Switchboards and Panelboards Explained

NEC article 408 switchboards panelboards: how short-circuit rating, field marking and panelboard protection work, with a worked check and a checklist.

By Shadai García, CEO and protection engineer at Tiza Group.

source1,000 kVA, 5.75 %switchboard35 kAcablepanelboard, 10 kA20.9 kApass12.4 kA at the panelboardfailPowerfull load: 1,202.8 A at 480 VIsc = 1,202.8 / 0.0575 = 20.9 kA35 kA is above 20.9 kA: passes10 kA is below 12.4 kA: failsshort-circuit current (kA)20.9available35ratingswitchboard12.4available10ratingpanelboardVerificationSourceAvailable currentRatingMarkingCheck© tizagrp.comsource1,000 kVA, 5.75 %switchboard35 kAcablepanelboard, 10 kA20.9 kApass12.4 kA at the panelboardfailPowerfull load: 1,202.8 A at 480 VIsc = 1,202.8 / 0.0575 = 20.9 kA35 kA is above 20.9 kA: passes10 kA is below 12.4 kA: failsshort-circuit current (kA)20.9available35ratingswitchboard12.4available10ratingpanelboardVerificationSourceAvailable currentRatingMarkingCheck© tizagrp.com
NEC Article 408: a 1,000 kVA, 5.75 % transformer feeding a 35 kA switchboard and a downstream 10 kA panelboard, with the available fault current compared against each rating. Location in the system and operating principle. Illustrative: real values come from the nameplate and the manufacturer's manual.
Short answer

NEC Article 408 governs switchboards, switchgear and panelboards as installed in the United States. Its core test is simple: the equipment's short-circuit current rating must be at least the fault current available at its line side. Around that sit rules on busbar arrangement, identification, panelboard rating and overcurrent protection. The listing standards (UL 891 and UL 67) decide how the equipment is built; the NEC decides how it is applied and marked.

NEC article 408 switchboards panelboards is the part of the National Electrical Code (NEC, NFPA 70) that tells a designer how this equipment must be applied on site. The question a reviewer asks most often about it is short: can this equipment withstand the fault current that the system can deliver to it?

The United States angle covers the short-circuit current rating, field marking and panelboard rules that the inspector checks. The wider framework is in the US electrical codes and grid interconnection guide. For the IEC-style view of assemblies, see the existing guide on the low-voltage switchboard and MCC.

Section numbers below follow the 2023 edition of the NEC. The 2026 edition, issued in 2025, expanded section 408.6, so check the numbering of the edition your authority having jurisdiction (AHJ) has adopted.

Short answer

Article 408 covers switchboards, switchgear and panelboards. Section 408.6 requires a short-circuit current rating (SCCR) at least equal to the fault current available at the equipment. Other sections cover busbar arrangement (408.3), circuit directories and identification (408.4), panelboard rating (408.30) and overcurrent protection on the supply side (408.36). Product standards such as UL 891 for switchboards and UL 67 for panelboards govern construction and listing.

What the article covers

Three kinds of equipment sit under Article 408:

  • Switchboards: large floor-standing assemblies with accessible fronts, usually carrying main and feeder devices.
  • Switchgear: assemblies with drawout power circuit breakers, used where higher ratings and withstand are needed.
  • Panelboards: wall-mounted or surface-mounted assemblies of branch circuit devices in a cabinet.

The article does not give you a catalog or a design method. It tells the designer what must be true once the equipment is installed: ratings against the available fault current, arrangement of conductors, labeling and protection of the board itself.

Short-circuit current rating: the central rule

Section 408.6 sets the rule: the short-circuit current rating of the equipment must not be less than the available fault current. Available fault current comes from the study of the system upstream: the utility source, the transformer and the conductors between them and the board.

Two points matter most in review:

  1. The rating applies to the assembly, not to one breaker. A main device with a high interrupting rating does not raise the rating of lower-rated busbars or branch devices.
  2. The study must exist before the equipment is ordered. The manufacturer needs the value to offer a suitable rating. Finding out afterward means a change order or a current-limiting solution.

Outside one- and two-family dwellings, the NEC also expects the available fault current and the date of its calculation to be marked in the field. How that marking is split between 408.6 and the general rule in 110.24 depends on the edition. The guide on NEC 110.24 available fault current marking covers the marking side. In the 2026 edition, 408.6 grew into a list. It also asks for the equipment’s own rating to be marked at its nominal voltage, and for the calculation to be redone after changes.

Arrangement, identification and panelboard rules

A few other sections come up in almost every project:

  • 408.3, support and arrangement of busbars and conductors. It covers the phase arrangement, the identification of a high leg on four-wire delta systems and bending space at terminals.
  • 408.4, field identification. Circuit directories must be clear and permanent. A feeder-supplied panelboard outside a one- and two-family dwelling must show where its power comes from, with a durable label that is not handwritten.
  • 408.30, panelboard rating. The rating of a panelboard must be at least the minimum feeder capacity, which the load calculation determines.
  • 408.36, overcurrent protection. A panelboard needs overcurrent protection on its supply side, rated no higher than the panelboard.

The same article has further rules on cabinets, damp locations, grounding bars, neutral terminals and the position of the panel. Use the full text of the edition you apply, because exceptions are common.

Where listing standards fit

UL 891 covers switchboards and UL 67 covers panelboards. The NEC asks for equipment that is listed for its use, and the listing carries the ratings the manufacturer has proven by test. The AHJ and the inspector rely on the nameplate and the listing mark, not on a statement in the drawings. This is why the specification should name the required SCCR and the listing, not only the continuous current. The IEC route works differently. See the guides on Icw, Ipk and Icc of an assembly and on the data needed to specify a low-voltage assembly. Both list data a manufacturer asks for.

For industrial control equipment that is not a switchboard or panelboard, see the sister guide on NEC Article 409 industrial control panels. Both guides depend on the same fault current value, and so does the arc flash label described in NEC 110.16 arc flash labeling.

Figure: single-line view of a transformer, a main switchboard and a downstream panelboard, with the available fault current and the short-circuit rating marked at each board.

Worked example: does the board withstand the fault current?

This example uses illustrative data, not data from any project. A 1,000 kVA transformer with 5.75% impedance feeds a 480 V, three-phase switchboard. Assume an infinite source on the primary, which is conservative.

  1. Full-load current: I = 1,000,000 / (1.732 × 480) = 1,202.8 A.
  2. Available fault current at the secondary terminals: I(sc) = 1,202.8 / 0.0575 = 20,918 A, about 20.9 kA.
  3. A switchboard with a 35 kA rating is above 20.9 kA, so it passes the 408.6 test at this point.
  4. Downstream, a branch panelboard is marked 10 kA. The study of the cable between them reports 12.4 kA at the panelboard, a value we assume for the example.
  5. 10 kA is below 12.4 kA, so the panelboard fails. The options are a panelboard with a higher rating, or a listed series combination that the manufacturer supports. Do not accept a note on the drawing as a substitute.

A real study uses the utility’s data, the actual cable lengths and motor contribution. The sequence matters more than the numbers: find the available current, compare with the assembly rating, then mark it and document it.

Checklist for the engineer

  • Confirm the NEC edition and amendments adopted by the AHJ.
  • Calculate the available fault current at every board and record the date and the assumptions.
  • Specify the SCCR of each switchboard, switchgear lineup and panelboard, not only the continuous rating.
  • Check that every downstream board has a rating at least equal to its own available current.
  • Name the listing standard (UL 891, UL 67 or the standard that applies) in the specification.
  • Plan identification: directories, source labels and the field marking the edition requires.
  • Check busbar arrangement, high-leg identification and bending space on the vendor drawings.
  • Confirm replacement or added devices have an interrupting rating that suits the marked fault current.
  • Keep the calculation where the people who inspect or maintain the board can find it.

Who signs and seals

In the United States a design normally has to be signed and sealed by a professional engineer licensed in the state of the project. The authority and the utility decide what they accept as evidence of the rating.

From the code to a design your engineer of record can stamp

If your project needs the single-line diagram, the fault current study and the switchboard specification, Tiza delivers engineering design ready for your engineer of record to review and stamp, remotely and in English. Tiza does not sign, seal or certify work in the United States. Contact us with the one-line diagram, the utility data and the edition your AHJ enforces.

Frequently asked questions

What is the difference between SCCR and AIC?

AIC (amperes interrupting capacity) belongs to a single overcurrent device and says what it can safely interrupt. SCCR, the short-circuit current rating, belongs to the whole assembly and says what it can withstand. An assembly can contain devices with a high AIC and still have a lower SCCR, so both values are checked against the available fault current.

Does Article 408 apply to a panelboard inside a house?

Article 408 applies to panelboards generally, including dwellings. Some marking and documentation items are limited to installations other than one- and two-family dwellings. The adopted edition and local amendments decide the exact scope, so the authority having jurisdiction is the place to confirm it.

Which edition of Article 408 should I design to?

The edition adopted by the state or city where the project is built. The 2026 edition expanded section 408.6, but many jurisdictions still enforce 2023 or earlier, sometimes with local amendments. Confirm the adopted edition before the design starts.

WhatsApp