The NEC 705.12 120% rule limits how much inverter current can feed a panel before the busbar is overloaded. The main breaker plus 125% of the source output current may total at most 120% of the busbar rating, with the source at the opposite end from the main. When the sum is too high, the designer can derate the main, upgrade the panel, connect on the supply side or use a power control system.
Anyone who adds solar or batteries to an existing panel meets this rule early. The panel has a busbar rating, a main breaker and little room left. The NEC checks the sum before the inspector passes the work.
Section numbers in this guide follow the 2023 edition of the NEC (NFPA 70). NFPA issued the 2026 edition in 2025, and many states and cities still enforce an earlier edition. Confirm the edition and the local amendments adopted where you build.
Short answer
The NEC 120% rule sits in the load-side connection provisions of section 705.12. It lets the main breaker rating plus 125% of the source output current total up to 120% of the busbar rating. The extra 20% is allowed only because the source sits at the opposite end of a busbar that carries loads. The two currents then never add at one point. If the sum exceeds 120%, the connection does not pass and the design must change.
Figure: a 200 A panel with the main breaker at one end of the busbar and the inverter breaker at the opposite end.
The US electrical codes and grid interconnection guide explains where the NEC sits among the other US documents.
Why the rule exists
A panel busbar is rated for the current it can carry along its whole length. In a normal panel, the main breaker feeds the bus at one end and the branch breakers draw current out along it. The main breaker protects the bus from overload by the utility.
A solar or battery inverter turns this around. It feeds current into the bus through its own breaker. Now two sources push current into the same copper. Each source breaker protects its own conductor, but no breaker protects the busbar from the sum of both. The utility can supply the full main-breaker current while the inverter supplies its full output. The bus between them then carries more than either breaker alone would show.
The 120% limit keeps that sum small enough for a bus designed with a margin. The opposite-end placement of the source breaker means the largest sum cannot occur at any single point of the bus. Position, not only rating, is part of compliance.
How to apply it
The check has four steps.
- Find the busbar rating on the panel label or listing, not the main breaker rating. They are often equal but not always.
- Find the main breaker rating that protects the bus.
- Size the source breaker from the inverter’s maximum continuous output current. The NEC treats this output as continuous, so the breaker is sized at no less than 125% of that current and rounded up to a standard rating. The standard ratings come from the overcurrent protection rules in Article 240, and the guide on NEC Article 240 covers them.
- Compare the sum. The main breaker rating plus 125% of the source output current must not exceed 120% of the busbar rating. The source breaker must be at the end of the bus opposite the main. The busbar check uses the current, not the breaker rating.
If more than one source is connected to the panel, add them all. A solar inverter and a battery inverter on the same panel both count.
Worked example
These are illustrative data, not from any project. A single-phase 240 V panel has a 200 A busbar and a 200 A main breaker.
- Allowed total: 120% of 200 A = 240 A.
- Room for source breakers: 240 A minus the 200 A main = 40 A.
- Inverter A is 7.6 kW. Output current: 7,600 W / 240 V = 31.7 A. Continuous factor: 31.7 A x 1.25 = 39.6 A. The source breaker is the next standard rating, 40 A.
- Check: 200 A + 39.6 A = 239.6 A, which is below the 240 A limit. It passes by 0.4 A, with the breaker at the opposite end of the bus.
- Inverter B is 11.4 kW. Output current: 11,400 W / 240 V = 47.5 A. Continuous factor: 47.5 A x 1.25 = 59.4 A. The source breaker is 60 A.
- Check: 200 A + 59.4 A = 259.4 A, which is above the 240 A limit. It fails.
Options for inverter B: replace the 200 A main with a 175 A main, if the service load calculation supports it. The room becomes 240 A minus 175 A = 65 A, and the 59.4 A fits. The alternatives are a panel with a higher busbar rating, a supply-side connection ahead of the main breaker, or a power control system. The last one is covered in the guide on NEC 705.13 power control systems.
The point is the order of the work: bus, main, source breaker, comparison. A reviewer who sees a 60 A source breaker on this panel will ask for the arithmetic.
What changes with batteries
A battery inverter counts as a source in the same check. It also complicates the design, because the battery can charge from the grid and discharge into the panel. The rules for storage sit in Article 706, covered in the guide on NEC Article 706 energy storage systems. The 120% check applies to the busbar either way.
When a system includes solar, a battery and backup loads, the panel often becomes crowded. A separate backup panel changes the busbar math, so the single-line diagram should show which sources feed which bus.
Common mistakes
- Using the main breaker rating as the busbar rating.
- Placing the source breaker next to the main breaker in the bus layout.
- Forgetting to add a second source on the same panel.
- Rounding the source breaker down to a standard rating instead of up.
- Adding the source breaker rating instead of 125% of the inverter output current.
- Assuming a derated main breaker needs no new load calculation.
- Citing a section letter from one edition against a project reviewed under another.
Checklist for the engineer
- Identify the NEC edition and local amendments the authority having jurisdiction (AHJ) enforces.
- Read the busbar rating from the panel listing or label.
- Record the main breaker rating and the position of every source breaker.
- Calculate each source’s maximum continuous output current from the nameplate, then size its breaker.
- Add every source connected to the panel and compare against 120% of the busbar rating.
- If the sum fails, document the chosen alternative and update the load calculation.
- Check the panel manufacturer’s listing for any added limit on backfed breakers.
- Show the panel, the breaker positions and the ratings on the single-line diagram.
- Keep the arithmetic in the drawing package so the reviewer can follow it.
For equipment that goes with this check, see the guides on rapid shutdown in solar systems and PV conductor sizing and raceways.
Who signs and seals
In most states a design package of this kind must be signed and sealed by a professional engineer licensed in the state of the project. Tiza delivers engineering design ready for your engineer of record to review and stamp. Tiza does not sign, seal or certify work in the United States.
How Tiza can help
If a panel fails the 120% check, Tiza prepares the interconnection design: busbar arithmetic, the chosen alternative and the single-line diagram. We deliver it remotely and in English, ready for your engineer of record to review and stamp. Send us the panel data and the inverter specification, and we will scope the work with you. Contact us to start.
Frequently asked questions
What is the NEC 120% rule?
It is a busbar check for a load-side connection of a solar or battery inverter. The rating of the main breaker plus 125% of the inverter output current cannot exceed 120% of the busbar rating. The source breaker is also placed at the opposite end of the bus from the main breaker.
How much inverter current does a 200 A panel allow?
With a 200 A main breaker on a 200 A busbar, the allowance is 120% of the busbar minus the main breaker, which is 40 A. That 40 A is 125% of the inverter output current, so the inverter may deliver up to 32 A. A smaller main breaker leaves more room. A larger one leaves less. Other panel limits can still apply, so check the panel listing.
What can I do if the inverter breaker does not fit under the rule?
Derate the main breaker if the load calculation allows it, replace the panel with one with a higher busbar rating, move the connection to the supply side of the service, or use a listed power control system that limits the current. Each option has its own code path, and your engineer of record should choose it.