The Electricity Safety, Quality and Continuity Regulations 2002, known as ESQCR, are public legislation on the safety of electrical networks. They bind generators, distributors, suppliers and meter operators, and their agents and contractors. They cover earthing, substations, underground cables, overhead lines, parallel generation and supplies to consumers. A developer meets them mostly through the network operator, which has to approve the connection and the earthing.
Most electrical standards tell you how to build. ESQCR tells network owners what they must not allow to happen, and a developer meets it through the connection offer, the earthing design and the overhead line clearances. The wider framework is in the UK electrical codes and grid connection guide, and the duty on employers and workers is covered in the Electricity at Work Regulations guide.
Short answer: what is ESQCR 2002?
The Electricity Safety, Quality and Continuity Regulations 2002 (ESQCR) impose requirements on the installation and use of electrical networks and equipment. These are owned or operated by generators, distributors (which include transmitters) and meter operators. The regulations also cover the part suppliers play in providing electricity. The regulations are public law, statutory instrument 2002 number 2665, and they are read on legislation.gov.uk. Offences are dealt with under section 29 of the Electricity Act 1989, and inspectors appointed by the Secretary of State may inspect under regulation 30.
Amendments in force
The regulations have been amended since 2002. The 2006 amendments (SI 2006/1521) added, among other changes, Part VA on trees. The 2026 amendments (SI 2026/848) changed regulation 22 from 27 August 2026 to admit plug-in solar devices that meet an interim product specification. The revised text on legislation.gov.uk carries all of them.
Who the regulations bind
Regulation 2 applies them to generators, distributors, suppliers and meter operators, and also to agents, contractors and sub-contractors who act on their behalf. Regulations 4, 15, 25, 26, 27, 28, 31 and 32 do not extend to those agents and contractors. For a designer or contractor working for a distributor or generator, this means the duty can reach you through your client.
How the regulations are organised
| Part | Regulations | Subject |
|---|---|---|
| I | 1 to 5 | Citation, application, general adequacy of equipment, co-operation, inspection |
| II | 6 to 10 | Electrical protection, neutral continuity, connection with earth, protective multiple earthing, earthing of metalwork |
| III | 11 | Substation safety |
| IV | 12 to 15 | Underground cables: restrictions, screens, depth, maps |
| V | 16 to 20 | Overhead lines: restrictions, height, position, warnings |
| VA | 20A | Trees and interference with supply |
| VI | 21 and 22 | Switched alternative sources and parallel operation |
| VII | 23 to 29 | Supplies to installations: failure, consumer premises equipment, connections, disconnection, information |
| VIII | 30 to 36 | Inspection, notification of events, exemptions, offences |
Schedule 2 holds the minimum heights of overhead lines. Schedules 3 and 4 hold the events and interruptions that must be notified.
The regulations a project meets
Regulation 3, general adequacy. Equipment must be suitable for its purpose and conditions, and built, installed and maintained to prevent danger and interference with supply so far as reasonably practicable. Generators and distributors must also assess the risk of interference, vandalism and unauthorised access to overhead lines and substations and apply safeguards that match the risk.
Regulations 8 and 9, earthing. The distributor earths the supply neutral, and on networks where the neutral and protective functions are combined, regulation 9 sets where the extra earth connections go. It also bars the connection of the combined conductor to metalwork in a caravan or boat. These rules explain why the earthing arrangement of a site, TN-C-S for example, is the distributor’s decision. See system earthing: TT, TN and IT.
Regulation 17 and Schedule 2, overhead lines. The clearance to the ground is judged at the maximum likely temperature of the line, when it sags most. Schedule 2 gives one height for lines over roads open to vehicles and another elsewhere.
Regulation 22, parallel operation. Nobody may install or operate a source of energy that can run in parallel with a distributor’s network unless conditions are met. The conditions are:
- equipment that prevents danger and interference, as far as reasonably practicable;
- suitable personnel and procedures;
- compliance with British Standard requirements, for a low-voltage consumer’s installation, or with the interim product specification, for a plug-in solar device;
- agreed requirements with the distributor.
A small-source exemption applies.
Regulation 24, equipment on the consumer’s premises. The distributor’s equipment on a consumer’s premises must be fit for purpose and protected by a fuse or circuit breaker close to the supply terminals.
Regulation 25, connections. Anyone who wants to make or change a connection to a distributor’s network needs the distributor’s consent. The distributor may not refuse unreasonably, and it must not consent if it has good reason to think that the installation does not meet British Standards or the regulations, or that the connection would be unsafe.
Worked example: the small-source threshold
The numbers are illustrative. Regulation 22 relaxes two of its conditions: the one on personnel and procedures, and the one on agreeing requirements with the distributor. The relaxation covers a low-voltage source of up to 16 A per phase that disconnects itself when the distributor’s supply is cut. The distributor must be told before or at commissioning.
- A three-phase inverter of 11 kW at 400 V: I = 11,000 / (√3 × 400) = 15.9 A per phase. That is within 16 A per phase.
- A three-phase inverter of 12 kW at 400 V: I = 12,000 / (√3 × 400) = 17.3 A per phase. That is above 16 A, so the full conditions apply, including an agreement with the distributor.
- A single-phase unit of 3.68 kW at 230 V: I = 3,680 / 230 = 16.0 A. That is right at the threshold and still within it, because the condition is not more than 16 A per phase.
The comparison is made with the current per phase, so the same power can be inside or outside depending on the number of phases and the voltage. The connection route for each size is explained in the UK electrical codes and grid connection guide.
Figure: a single-line diagram of a distribution network, the point of connection to a generator, the protection that disconnects it when supply is lost and the earthing of the site.
Common problems in practice
- Assuming the regulations bind only the network operator, when a generator is also bound.
- Choosing the earthing arrangement of a site before the distributor has said what it offers.
- Forgetting that the distributor’s consent is required before a connection is made or changed.
- Quoting the number of a regulation from memory without checking the revised text.
- Treating compliance with ESQCR as the same as compliance with BS 7671. They apply to different parties and different parts of the system.
Checklist for the engineer
- Identify which role the client has: generator, distributor, supplier or meter operator.
- Read the revised regulations on legislation.gov.uk for the sections that apply.
- Agree the earthing arrangement and the connection requirements with the distributor.
- Check the parallel operation conditions for each generating or storage source.
- Check clearances of any overhead line against Schedule 2 with the line temperature in mind.
- Record the sources for the reviewing engineer.
Legal frame
In the UK there is no statutory stamp for electrical design drawings. A chartered engineer or other competent person reviews the design and signs it under their own responsibility, and the duty holders named in the regulations remain responsible for compliance. For a legal reading of a specific case, take advice from a qualified adviser.
How Tiza can help
If your project connects generation or storage to a distribution network, Tiza prepares the engineering design and the studies behind the application remotely and in English: single-line diagram, earthing assessment, fault levels and the protection approach. Tiza does not stamp, sign or certify designs in the UK; we deliver engineering and studies ready for your chartered engineer to review and sign. Contact us with the site data and the network operator’s requirements.
Frequently asked questions
Who must comply with ESQCR 2002?
Regulation 2 applies the regulations to generators, distributors, suppliers and meter operators, and to their agents, contractors and sub-contractors acting on their behalf. A customer with an ordinary installation is not directly bound, but the distributor must comply when it connects that installation.
Does ESQCR apply to a solar farm or battery connected to the network?
Yes, where the owner is a generator. Regulation 22 sets conditions for anyone who installs or operates a source of energy that may run in parallel with a distributor's network, including equipment to prevent danger and an agreement with the distributor.
Where can I read ESQCR?
On legislation.gov.uk, where it is published as statutory instrument 2002 number 2665. It is public law, so there is no charge to read it. Read the revised version there, because the regulations have been amended several times, most recently in 2026 for plug-in solar devices.