Tiza Group

Home / Guides / Codes and grid connection: US, UK, CA, AU

S5.2.5.8 Protection from Power System Disturbances

What NER clause S5.2.5.8 asks of generator protection: no trip when the plant must ride through, fast power cuts on over-frequency, and a worked example.

By Shadai García, CEO and protection engineer at Tiza Group.

33 kV busplant breakerVT 33,000/110 VCT2,500/1plantcontroller81 / 27frequency, U blockramp command=~inverters120 MW plant, 96 MWPowerMeasure / controloutput before the event: 96 MWhalf within 3 s: 96 / 2 = 48 MWramp 48 / 3 = 16 MW/s = 13.3 % of 120 MWCT: 2,099 A at 2,500/1 gives 0.84 AVT ratio 300: block at 0.8 pu = 88 VMWt (s)0123964816 MW/sillustrative valuesRide-throughVT frequency81 / 27Plant controllerRampInverters© tizagrp.com33 kV busplant breakerVT 33,000/110 VCT2,500/1plantcontroller81 / 27frequency, U blockramp command=~inverters120 MW plant, 96 MWPowerMeasure / controloutput before the event: 96 MWhalf within 3 s: 96 / 2 = 48 MWramp 48 / 3 = 16 MW/s = 13.3 % of 120 MWCT: 2,099 A at 2,500/1 gives 0.84 AVT ratio 300: block at 0.8 pu = 88 VMWt (s)0123964816 MW/sillustrative valuesRide-throughVT frequency81 / 27Plant controllerRampInverters© tizagrp.com
NER S5.2.5.8: a 120 MW solar farm at 33 kV with its breaker, CT and VT, the plant controller that ramps the output down to the inverters, and the 81 and 27 backstop relay fed by the VT only, with a 96 MW output cut to 48 MW in 3 seconds at 16 MW per second. Location in the system and operating principle. Illustrative: real values come from the nameplate and the manufacturer's manual.
Short answer

Clause S5.2.5.8 of the National Electricity Rules, titled protection from power system disturbances since 21 August 2025, limits what a plant's own protection may do. It must not trip the plant for conditions the plant has to ride through, and a larger plant must cut its output quickly when frequency runs high.

Clause S5.2.5.8 of the National Electricity Rules (NER) is titled “Protection from power system disturbances”. Before 21 August 2025 its title was “Protection of generating systems from power system disturbances”. It sits in Schedule 5.2, the schedule that sets technical conditions for generators connecting to the National Electricity Market. The clause answers a narrow question: when may the plant’s own protection disconnect the plant, and when must it keep the plant on line? The Australian Energy Market Operator (AEMO) assesses it with the network service provider.

The clause is one of the generator performance standards (GPS) described in the Australia electrical codes and grid connection guide. For the engineer, it turns into relay settings and a protection report.

Short answer

S5.2.5.8 says the plant’s protection must not disconnect it for conditions it is required to ride through. Above a size threshold, it also requires facilities that cut output rapidly when frequency is too high. The 2025 text adds ride-through of a sudden shift in the voltage phase angle.

What the clause says, in plain words

  • Protection must not defeat ride-through. The network service provider (NSP) or the plant owner may require automatic disconnection for abnormal conditions. The protection must still not disconnect the plant for conditions it must ride through under the NER. Those conditions are set in the neighbouring clauses on frequency, voltage and disturbances.
  • Over-frequency power reduction. Above the size threshold, the plant needs facilities that reduce active power automatically by at least half within 3 seconds when frequency exceeds a set level. The level depends on the region’s frequency operating standard.
  • Voltage phase angle shift. The plant must not trip for a sudden shift in the voltage phase angle within the limits the clause sets.
  • Trip and no-trip conditions. The performance standard records which protection may disconnect the plant, with its settings, so AEMO and the NSP can keep the system secure.

Clause 5.3.4A sets how any level below the automatic access standard is assessed. The question is whether every trip path in the design stays outside the ride-through conditions.

Why ride-through and protection collide

A generating plant carries protection for itself: voltage, frequency, rate of change of frequency, current unbalance and converter fault codes. Each is a trip path. Any path set tighter than the ride-through envelope in the neighbouring clauses will disconnect the plant during an event it should survive. The system then loses more generation at the worst moment.

For asynchronous plants such as solar and battery inverters, the common trap sits inside the converter. Counters for undervoltage or overvoltage events, and internal error lists that stop the unit, can act like protection even though nobody set them in a relay. Assessors ask for them to be declared. A practical view of the same problem is in why inverters disconnect from the grid.

Over-frequency reduction in practice

Frequency high means the grid has more generation than load. The standard asks the plant to remove at least half of its output in seconds. The assessor expects evidence from both RMS and EMT simulation (root-mean-square and electromagnetic transient models). It also expects a record of how the inverter or governor controls produce the reduction.

The relay does not do this alone. The frequency element is one input. The plant controller or the inverter firmware is what ramps output. A protection engineer should set the relay stage as a backstop above the controller action, with a definite time that the controller cannot satisfy by itself. The guide on the operating and reset characteristic of protection 81 covers pickup, reset and supervision of the frequency element.

Worked example (illustrative)

The numbers are illustrative. A 120 MW solar farm connects at 33 kV and its output before the event is 96 MW. Frequency exceeds the trigger level, and the plant must reduce output by at least half within 3 seconds.

  1. Required reduction: at least half of 96 MW, which is 48 MW.
  2. Time allowed: 3 s. Required average ramp: 48 / 3 = 16 MW per second, or 960 MW per minute.
  3. As a share of plant rating: 16 / 120 = 13.3 percent of rated power per second. The inverters and the plant controller must be able to do this, not only the relay.
  4. Rated current at 33 kV and unity power factor: 120 000 kW / (1.732 × 33 kV) = 2 099 A. A 2 500/1 A current transformer (CT) leaves about 0.84 A on the relay at full output.
  5. Voltage supervision: a 33 000/110 V voltage transformer (VT) has a ratio of 300. An undervoltage block at 0.8 per unit acts below 33 000 × 0.8 / 300 = 88 V phase to phase on the secondary. During a fault, the voltage collapses and phase jumps can distort the frequency measurement. The block stops the backstop stage from tripping the plant during a fault it must ride through.

The result: the controller must deliver 16 MW per second. The relay stage must not pick up inside the continuous operation band, and its undervoltage block must hold it during faults.

Checklist for the engineer

  • Protection single line diagrams showing CTs, voltage transformers (VTs), relays and the breaker tripping logic.
  • A settings table with the derivation of each element’s pickup and time, compared against the ride-through envelope.
  • Confirmation that none of the elements can operate inside continuous uninterrupted operation.
  • Declaration of converter counters, error lists and any internal trips for asynchronous plants.
  • Evidence of the over-frequency power reduction in RMS and EMT models, if the plant is above the size threshold.
  • Islanding scheme, where AEMO or the NSP requires one, and its communications path.
  • A written list of the conditions for which the plant must trip and must not trip.
  • Suitability check of the protection CTs and a letter from the NSP confirming a coordinated interface design.

Figure

Figure: single line of a 33 kV solar plant with CT, VT, frequency relay and breaker, the control path to the inverters and the protection trip path to the breaker.

Next step

If your plant is heading for a submission to AEMO and the NSP, Tiza provides remote relay configuration in English: the protection settings plan and its derivation. Tiza does not stamp, sign or certify the work: it delivers engineering ready for review and certification by your RPEQ in Queensland, or by the registered engineer your state requires. Contact us with the single line diagram and the connection requirements.

See also clause S5.2.5.9 on protection and security, clause S5.2.5.10 on tripping for unstable operation, clause S5.2.5.11 on frequency control, protection coordination step by step and the SEL-700G generator relay.

Frequently asked questions

Why do older documents give S5.2.5.8 a different title?

Before 21 August 2025 the clause was titled protection of generating systems from power system disturbances. The Improving the NEM access standards, Package 1 rule renamed it protection from power system disturbances, because Schedule 5.2 now applies by plant type.

Does an over-frequency power reduction apply to every plant?

No. The rapid reduction applies above a size threshold set in the clause, the same one used for partial load rejection. Below it, the rule against tripping inside the ride-through envelope still applies.

Who checks the protection settings for this clause?

AEMO assesses the proposed standard together with the connecting network service provider, which also confirms the interface design is coordinated with its own protection. The engineer of record for the project reviews and certifies the settings report before it is submitted.

WhatsApp