Tiza Group

Home / Guides / Codes and grid connection: US, UK, CA, AU

AS/NZS 5139 Battery Installation in Australia Explained

AS/NZS 5139 battery installation explained: restricted locations, barriers, DC protection and the AS/NZS 4777.1 link, with a worked fault current example.

By Shadai García, CEO and protection engineer at Tiza Group.

battery locationmodule 1module 2module 3DC protective device=~battery invertermain switchboardloadsbattery module 51.2 V, 20 mohmcable and connections add 5 mohmone module: 2048 Atwo in parallel: 3413 Athree in parallel: 4389 Adevice breaking capacity above 4389 A1 module: R = 0.025 ohm2048 A2 modules: R = 0.015 ohm3413 A3 modules: R = 0.01167 ohm4389 AR = 0.020 / n + 0.005 ohm; I = 51.2 V / Rprotective device: breaking capacity above 4389 Athe manufacturer's figure replaces this estimateillustrative valuesBatteryModuleDC deviceInverterBoardLocation© tizagrp.combattery locationmodule 1module 2module 3DC protective device=~battery invertermain switchboardloadsbattery module 51.2 V, 20 mohmcable and connections add 5 mohmone module: 2048 Atwo in parallel: 3413 Athree in parallel: 4389 Adevice breaking capacity above 4389 A1 module: R = 0.025 ohm2048 A2 modules: R = 0.015 ohm3413 A3 modules: R = 0.01167 ohm4389 AR = 0.020 / n + 0.005 ohm; I = 51.2 V / Rprotective device: breaking capacity above 4389 Athe manufacturer's figure replaces this estimateillustrative valuesBatteryModuleDC deviceInverterBoardLocation© tizagrp.com
Single-line diagram of a battery system under AS/NZS 5139: up to three battery modules in parallel inside the battery location, the DC protective device, the battery inverter and the main switchboard, with a DC fault between the device and the inverter and the worked estimate of the prospective current: 2048 A for one module, 3413 A for two and 4389 A for three, from 51.2 V, 20 milliohm per module and 5 milliohm of cable. Location in the system and operating principle. Illustrative: real values come from the nameplate and the manufacturer's manual.
Short answer

AS/NZS 5139:2019 sets the safety requirements for installing battery systems that connect to inverters in Australia. It limits where a battery system may be placed, requires barriers and clearances, and treats the battery's DC protection and the combined system as one design. Amendment 1:2025 updates it, and a DC short-circuit current example shows how the protective device rating is checked.

Batteries add a fire and energy hazard that a PV array does not have, and AS/NZS 5139 is the standard written for it. It covers the battery system as a product and as an installation: where it may be placed, how it is protected, and how it connects to the inverter. The wider framework is in the Australia electrical codes and grid connection guide.

Short answer: how does AS/NZS 5139 govern battery installation in Australia?

AS/NZS 5139 sets safety requirements for battery systems that connect to inverters. It limits where a battery system may be installed and requires clearances and barriers. It defines protection and isolation on the DC side. It treats the battery and its power conversion equipment as one system, with manufacturer instructions that must be followed. It works with AS/NZS 4777.1 for the inverter connection and with AS/NZS 3000 for the wiring.

Editions

AS/NZS 5139:2019 is the current edition, now with Amendment 1:2025, published in December 2025. In Western Australia, electrical licence holders must comply fully with the amended edition from 19 June 2026. Industry bodies such as the Clean Energy Council have published advice on how to apply it, and state regulators publish their own guidance and defect examples. Adoption dates and transition arrangements differ by state, so confirm what applies where the project sits. If a newer edition appears in the Standards Australia catalogue, that edition prevails.

How the standard thinks about risk

The standard is built around three ideas.

  1. Keep the hazard away from people. A battery system must not be placed in restricted locations, such as habitable rooms, ceiling spaces, wall cavities and escape routes. Clearances apply to exits and to openings into habitable rooms, and a barrier is required in some wall arrangements.
  2. Contain a failure. The installation should limit how a fault in one battery module spreads: protective devices on the DC side, suitable enclosures, and room or enclosure ventilation where the manufacturer asks for it.
  3. Make the system understandable. Labels, isolation points and documentation allow the owner and an emergency responder to understand the system.

The battery system as a design unit

The design needs the battery system’s data sheet and instructions as inputs. The standard treats the manufacturer’s instructions as binding, so the installation is only as good as the data the designer collects. The parts to document are:

  • Battery modules and their management system, with nominal voltage and capacity.
  • The DC protective device between the battery and the inverter, with its breaking capacity.
  • The inverter, whether it is a hybrid or a battery inverter, and its listing under AS/NZS 4777.2. See AS/NZS 4777.2 inverter requirements.
  • The location, enclosure, ventilation and distances to exits and openings.
  • The cable sizes and routes on the DC side.

For the technology and ageing side, see lithium-ion batteries: safety and service life. For AC or DC coupling and system layout, see hybrid solar system with batteries. The inverter installation side is in AS/NZS 4777.1 installation and commissioning.

Figure: single-line diagram of a battery system with modules, DC protection, the battery inverter and the main switchboard, with the restricted-location boundary of the room.

Worked example: DC short-circuit current at the battery

These values are illustrative. Real figures come from the battery manufacturer. A battery module has a nominal voltage of 51.2 V and an internal resistance of 20 mΩ. The DC cable and connections add 5 mΩ in total. The system uses one, two or three modules in parallel. As a first estimate, the battery’s short-circuit current is the nominal voltage divided by the total resistance.

  1. One module: R = 0.020 + 0.005 = 0.025 Ω. Current = 51.2 / 0.025 = 2048 A.
  2. Two modules in parallel: R = 0.020 / 2 + 0.005 = 0.015 Ω. Current = 51.2 / 0.015 = 3413 A.
  3. Three modules in parallel: R = 0.020 / 3 + 0.005 = 0.01167 Ω. Current = 51.2 / 0.01167 = 4389 A.

The prospective fault current grows with every module added, but not in proportion, because the cable resistance stays the same. The DC protective device must have a breaking capacity above the largest of these values, with the manufacturer’s own figure replacing this estimate. A rule of thumb: confirm the DC device rating every time capacity is added, because it is easy to expand a battery and forget the protection.

Sizing the room and the protection

Two habits prevent most rework. First, size the location before the equipment: the battery footprint, the clearances to exits and openings, and the barrier needed all take space, and a late move can force a change of battery or inverter. Second, treat the DC protective device as part of the battery system, not of the inverter. Its rating, the cable between the two and the isolation point must be consistent with the manufacturer instructions, and with the labelling the installer leaves at the switchboard.

Checklist for the engineer

  • Confirm the edition required by the state regulator and the installer’s accreditation scheme.
  • Collect the battery data sheet and instructions, including fault current and ventilation needs.
  • Check the location against the restricted-location list, the clearances and the barrier rule.
  • Calculate prospective DC fault current and select a protective device with sufficient breaking capacity.
  • Confirm the inverter listing and the interface to AS/NZS 4777.1.
  • Prepare the labelling and the isolation procedure.
  • Document the system so that the owner and a responder can read it.

Small battery systems are installed by licensed or accredited installers under state electrical safety rules. Where an engineering design is needed, professional engineering services in Queensland must be provided by or under the direct supervision of an RPEQ, and Victoria has required registration for electrical engineers since 2023. Other states and territories set their own rules. Tiza delivers engineering and studies ready for your RPEQ in Queensland, or the registered or chartered engineer your state requires, to review and certify. Tiza does not stamp, sign or certify.

How Tiza can help

If your project needs the engineering design for a battery system, Tiza prepares the single-line diagram, the DC protection and fault current calculation and the equipment schedule remotely and in English. Contact us with the battery data and the site layout.

Frequently asked questions

Where can a battery system not be installed under AS/NZS 5139?

The standard lists restricted locations, which include habitable rooms, ceiling spaces, wall cavities and escape routes, and it sets clearances from exits and from openings into habitable rooms. Where a battery sits on or near a wall of a habitable room, a barrier may be needed. The exact distances and conditions are in the clauses, and the regulator may add guidance.

Is AS/NZS 5139 the same as AS/NZS 4777.1?

No. AS/NZS 5139 covers the installation of the battery system. AS/NZS 4777.1 covers the inverter energy system and its connection to the installation. A system with a battery inverter must satisfy both, together with AS/NZS 3000 for the wiring.

Which edition of AS/NZS 5139 is current?

AS/NZS 5139:2019 with Amendment 1:2025, published in December 2025. In Western Australia, licence holders must comply with the amended edition from 19 June 2026, and other states set their own dates. Check the regulator for the state where the project sits.

WhatsApp