The NEC is one enforceable code with prescriptive rules, written for North American practice. IEC 60364 is a series of installation standards that countries adopt and adapt nationally. They share goals but differ in structure, voltage, earthing vocabulary and how rules are enforced. Design across both by working from the code the local authority enforces, not by translating clause to clause.
Designers moving between North America and the rest of the world soon ask what NEC vs IEC 60364 means in practice. Both aim at safe low-voltage installations, but they are built differently and enforced differently. The differences that matter to a designer are scope, structure, voltage, earthing, protection and verification. No clause-by-clause equivalence exists between them.
Short answer
NEC vs IEC 60364: the NEC (NFPA 70) is a single code with prescriptive rules, adopted into law by states and local authorities in the United States. IEC 60364 is a series of international installation standards, adopted nationally with local changes. Do not convert one into the other. Identify which document the authority enforces and design to it, using the other only as background.
The NEC edition referenced here is 2026, issued by NFPA in 2025; many jurisdictions enforce earlier editions. IEC 60364 is a multi-part series, and parts have different publication years, so check the part and edition you cite.
How they are built
- The NEC is a single document organized in chapters and articles, revised on a three-year cycle. It tells the designer what to do, often with tables of values and exceptions. It is enforced where an authority adopts it.
- IEC 60364 is a series of parts covering fundamental principles, protection for safety, selection and erection of equipment, verification and special installations. Each part is a standard, and countries publish national versions. The IEC text is a model; the legal text is the national one.
A design reviewer under the NEC checks against articles. A reviewer under an IEC-based national standard checks against the national standard and its relevant parts. Their questions overlap but their order does not.
Where they differ in practice
| Topic | NEC practice | IEC 60364 practice |
|---|---|---|
| Typical LV supply | 120/240 V, 208Y/120 V, 480Y/277 V | 230/400 V |
| Earthing language | Grounded system, grounding electrode, bonding | TN-S, TN-C-S, TT, IT |
| Protection against shock | Ground-fault circuit interrupters (GFCI) required in listed locations; arc-fault devices are a separate fire-protection rule | Residual current devices and disconnection times set by earthing system |
| Verification | Inspection by the authority; acceptance testing by project | Initial verification and periodic inspection are explicit parts of the standard |
| Product approval | Listing and labeling by recognized laboratories | CE or national marks and product standards |
| Enforcement | State and local adoption | National regulation |
The supply voltage difference matters in sizing. The same load draws more current at lower voltage, so conductors, breakers and losses change.
Protection and overcurrent devices
Both documents require protection against overload and short circuit, but they express it differently. The NEC sets ampacity tables and standard overcurrent device ratings, and relies on listed equipment with short-circuit current ratings marked on it. IEC-based practice coordinates the device characteristic with the conductor and the prospective fault current at its location. It also verifies disconnection times for the earthing system in use. In both cases the designer must know the available fault current at each point. The NEC asks for it to be marked on certain equipment, and the IEC approach asks for it in the verification. Do not reuse a device selection made for one voltage and earthing system on the other.
Earthing and grounding vocabulary
IEC classifies systems by how the supply and the exposed conductive parts are connected to earth (TN, TT, IT). The NEC describes how the system and equipment are grounded and bonded, with prescriptive rules for grounding electrodes, equipment grounding conductors and main bonding. Drawing a TN-S diagram for a US reviewer produces confusion; redraw it in the vocabulary of the code in force. See PE circuit continuity and cross-section for the IEC side of the question and grounding practice compared for the wider comparison.
Figure: a 480Y/277 V US feeder with its grounded neutral and main bonding jumper, beside a 400/230 V TN-S feeder with separate neutral and protective conductors.
Worked example: the same 10 kW load on two systems
Take an illustrative balanced three-phase 10 kW load at unity power factor, fed through the same conductor in both cases:
- At 480 V: I = 10,000 / (1.732 × 480) = 12.0 A.
- At 400 V: I = 10,000 / (1.732 × 400) = 14.4 A.
- The current ratio is 14.4 / 12.0 = 1.2, which equals 480 / 400.
- Conductor losses go with the square of the current, so with the same conductor resistance the 400 V case dissipates (1.2)² = 1.44 times the loss.
So moving a design from one voltage to the other is never a copy-and-paste: protection ratings, conductor sizes, voltage drop and losses all shift. The lesson is to rerun the calculations with the local voltage and the local tables, and not scale old numbers.
Special installations
IEC 60364 groups special installations and locations in Part 7, for example photovoltaic power supply systems in Part 7-712. Low-voltage generating sets sit in section 551 of Part 5-55. The NEC places similar content in articles, such as Article 690 for photovoltaic systems and Article 705 for interconnected power sources. Locating the rule is the first task when you move between the two. The answer may sit in a different part, a different chapter or a different national supplement. National versions of IEC 60364 often add local rules for utilities and regulators, so the national text always prevails over the model.
Checklist for the engineer
- Identify the document the authority enforces and its edition.
- Confirm supply voltage, frequency and earthing system with the utility.
- Redraw earthing and bonding in the vocabulary of the enforced code.
- Rerun conductor sizing, voltage drop and protection selection with local rules.
- Confirm product approval: listing in the US, conformity marking elsewhere.
- Confirm testing and documentation requirements for acceptance.
- Check the same facts in the guides on conductor sizing in PV systems and the US framework.
Related guides
Back to the comparison hub. See also NEC, BS 7671, AS/NZS 3000 and CEC compared and the Australian framework. For rules specific to arc and fault energy, see arc flash PPE categories, how to reduce incident energy and electric shock in a substation.
How Tiza can help
If a design made under one code has to be adapted to another, an independent review by Tiza lists the clauses and calculations that no longer hold. Tiza does not stamp, sign or certify; we deliver the review and the adapted engineering ready for your engineer of record to review and stamp. Contact us with the drawings and the code that applies.
Frequently asked questions
Is IEC 60364 mandatory?
Not by itself. IEC 60364 is a series published by the IEC, and each country decides whether to adopt it, usually through a national standard with local changes. The legally binding document is the national or regional rule that the authority enforces, so always design to that.
Can I design to the NEC and call it equivalent to IEC 60364?
No. Equivalence is a judgment for the authority having jurisdiction, and the two documents differ in structure, voltages, earthing and testing rules. A design that is correct under one can fail review under the other. Use the code the authority enforces.
Which earthing system terms differ?
IEC uses the TN, TT and IT classification with letters for the supply and the installation. The NEC speaks of grounded and ungrounded systems, grounding electrodes and bonding. The ideas overlap, but a TN-S drawing is not an NEC drawing, so redraw in the vocabulary of the code you apply.